Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).Ecomaterials, or "Green Materials", are those designed so as to minimize their environmental impact, while still maintaining or even increasing the desired operational performance. Ecomaterials research is an interdisciplinary field where scientists and engineers with backgrounds in both chemistry, and in materials such as metals, ceramics, polymers, and carbon, are involved in raising the environmental consciousness of industry and in motivating ecological research. This volume contains the papers presented during the fourth international symposium on ecomaterials processing and design, which was held on February 4-6, 2003 in Kangnung, Korea.
The book is divided into five sections: the first section deals with the use of non-hazardous alternatives as substitutes for traditional, but hazardous, components. The second section covers the incorporation of an end-of-life strategy into materials design. The third section covers the treatment of waste materials. The fourth section envisions manufacturing as being a more environmentally-friendly process. The final section treats the development of environmentally functional materials. Altogether, this volume constitutes an invaluable blueprint for a healthier millennium.
Chapter
TiO2-Coated Plastic Optical Fibers for Purification
Porosity Variation on the Compressive Deformation of Pre-Sintered Al-Si-Fe Based Alloy
Mechanical Characteristics of Mg and its Composites Recycled from Mg Chips
Viscosity and Surface Tension of Al and Effects of Additional Element
Tin-Cobalt Alloy Plating in a Pyrophosphate Bath
Porosity-Grading Porous Materials by Centrifugal Sintering
Improvement of Strength in Porous Ceramics by Control of Additives
Microstructure and Mechanical Behavior of Porous/Dense Alumina Multilayer Composites
Microstructure and Wear Properties of Al2O3/TiO2 Nanocomposites
Preparation of Fine Alumina Dispersed Ytterbia-Stabilized Cubic Zirconia Based Composites
Fracture and Tribological Behaviors of Al2O3 / 5 vol.% SiC Nanocomposites
Effect of Chemical Composition on the Grain Orientation of Alumina in Oxide Laminate Composites
Effect of Silicate Addition on the Microstructure Texturing of Alumina Laminate Composites
Synthesis of Calcium Sulfoaluminate Clinker Using Alunite
Effect of WC Particle Size on Grain Growth Inhibition in the WC-xVC-Co System
Mechanical and Thermal Properties of Hot-Pressed Si3N4 with Added AlN
Effect of Compaction Pressure on the Microstructure Evolution of Anode Substrate for SOFC Application
Properties of Hot-Pressed AlN/BN Nanocomposites
Measurement Method of Carbon Char Content from Industry Sludge
Hydrogen Treatment of Ti Scrap
Effect of Viscosity on the Separation of Copper from Al2O3-CaO-SiO2-10wt%MgO Slag System
Improvement of Silver Recovery Efficiency by High-Speed Rotation
Synthesis of Ordinary Portland Cement Clinker Using Waste POSCO Sludge
Characterization of Waste Vinyl from a Farm Village and its Application to Cement Kiln Process
Characterization of Glass Abrasive Sludge and its Reutilization as a Cement Admixture
Production and Properties of Glass-Ceramic from Incinerator Fly Ash
Silica Honeycomb-Crystal Structure Prepared by Fabrication of Silica-Coated Particles
Effect of Gas Bubbling and Impeller Agitation on Degassing Kinetics during Magnesium Alloy (AZ91D) Melt Recycling – Water Model Approach
Flow Modeling in Negative-Pressure Infiltration Casting Process of Aluminum Open-Cell Fabrication
Discharged Photoelectrocatalytic System for the Enhancement of Photocatalytic Performance
Adsorption of Heavy Metal Ions onto the Surface of Metal-Incorporated Hydrous Ferric Oxide Particles
Effect of Phosphorus or Boron Addition on Water-Resistance of Water-Glass Adhesives
Fabrication and Sagging Behavior of Three-Layer Al-Si/Al-Mn-Zn/Al-Si Clad Sheets for Automotive Heat Exchanger
Improvement in Mechanical Properties of Magnesium Alloy (AZ31) Sheet Fabricated by Casting and Subsequent Plastic Working
Fabrication of Various Nano Noble Metal Composite Materials by Ecological Sono-Process
Evaporation Behavior of Magnesium under Reduced Pressure
Influence of Final Crystal with Synthesis of Basic Calcium Carbonate by Carbonation Process
Fabrication of Metastable Oxide Ceramics with Oxygen Vacancy
Sintering Behavior and Electrical Properties of (Bi1/2 Na 1/2) 0.99Ca0.01TiO3 Ceramics by Two-Stage Calcination Method
Effect of Different Annealing Condition on Bake Hardenability for Environmental Automotive Panel
Preparation of TiO2 Fiber and Its Photocatalytic Properties
Plasma Model in Aluminum Nano-Films
Effect on Compression Properties of Al Alloy Foam Materials by Added Si
Effect of TiO2 Powder Size on the Reactivity of Photocatalyst
Mechanical Properties of Ti3SiC2 Synthesized by Reaction Sintering
Organism Resolution Ability of Titania Photocatalyst in Water
Synthesis and Photocatalytic Properties of Nano TiO2 Coated on Fly Ash
Nano-Scaled Microstructure and Tensile Behavior of Spray-Formed and Subsequently Worked Al-8Fe-2Mo-2V-1Zr Alloys
Precipitation Behavior and Mechanical Properties of a Supersaturated Co-Based Superalloy
Polypyrrole-Based Methanol Sensors Prepared by Chemical and Vapor State Polymerization
Sensing Mechanism of Conducting Polymer Sensor for Volatile Organic Compounds
Apatite-Coated Titanium Dioxide Photocatalyst
Volatile Organic Gas Recognition Using Conducting Polymer Sensor Array
Fabrication and Sensing Behavior of NASICON Thick Film SO2 Gas Sensor by Screen-Printing Method
Fabrication and Microstructure of Pt/SiO2 Composite Membranes by a Reverse Micelle and Sol-Gel
Gas Sensing Properties of Nanocrystalline ITO Thick Films with Different Particle Sizes
Eco-Materials Processing & Design IV
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
