Chapter
A Study of Turning Operation by Oil-Water Combined Mist Lubrication Machining Method
Research on Enhancing Heat Transfer in Grinding Contact Zone with Radial Water Jet Impinging Cooling
Significance of Grinding Temperature in Metal Removal
Stone Sawing Forces by Single Diamond Segment
Study on Surface Grinding of Granites with Resin Bonded Diamond Wheel
Compliant EDM for Free-Form Surfaces Polishing
Study on Performance of CBN Cup Quill for Face Grinding
Experimental Research on Flow during CMP Processes
The Application of the Lubrication Theory to the Surface Grinding
Theoretical Analysis of Temperature Field in Surface Grinding with Cup Wheel
Development of a Dicing Blade Using Light-Hardening Resin
Ultra-Precision Grinding of Ceramic Glass with ELID Technique
Surface Integrity and Modification of Diamond Wheel Ground Engineering Ceramics
Experimental Study on the Single-Grit Grinding Titanium Alloy TC4 and Superalloy GH4169
Study of the Formation and Propagation Conditions of Grinding Crack for Ceramics
The Preparation of Super-Fine Alumina Powders with Sol-Gel Technology
The Mathematical Model for Center Movement of Grinding Wheel while Grinding Cam Part with NC Grinder
Truing of Diamond Wheels by Laser
Microanalysis of Interface between Ni-Cr Alloy and Diamond (or Steel)
Brazing of Ti/Ni-Coated Diamond
Evaluation for Adhesion Performance of Brazed Grains
Investigation on Brazing of Single-Layer Superabrasive Wheel
Improvement of Adhesive Strength and Surface Roughness of Diamond-Coated Thin Film Tools
Polishing of CVD Diamond Films
Lap-Grinding of Al2O3 Ceramics Assisted by Water-Jet Dressing Metal Bond Diamond Wheel
Zirconia-Toughened Si3N4 Bonding Polycrystalline Cubic Boron Nitride (PCBN)
Research on Grinding Wheel Intelligent Dressing System
Rubbing Process Technology of HIPSN Ceramic Balls
On-Line Intelligent Identification in Grinding Process Based on Rough Sets Theory
Form Grinding Technology of an Irregular Roller and the Electrolytic In-Process Dressing for the Form Grinding Wheel
Effect of Ti Coating on Wear Stages of Diamond in Tools
Experimental Models Coupled Optimal Design of Multi-Blade Sawing with Diamond Abrasive Tools
On the Transverse Vibration of Circular Saw
Development of CBN Wheel with Cold Gas Inner Cooling
Simulation and Optimum for Plunge Grinding
The Critical Velocity Model and Surface Characteristics of Mixed Longitudinal Ultrasonic Honing
New Ultra-Precision Polishing Techniques of Glass BK-7 Optical Plate
The Boring-Grinding-Rolling Techniques for Hydraulic Cylinder of 0.2% Carbon Steel
Study on New Type of Matrix Material of Electroplating Diamond Tools
Analysis of On-Line Roll Grinding Technology for Hot Strip Mill
Research on Complex Ultrasonic Honing Acoustics System by Statistical Energy Analysis
Modeling and Simulation of Virtual Grinding Machine
The Technology of Laser Honing Applied in Distinctively Improving the Lubrication of Frictional Units
Study on Concurrent Engineering-Based CAPP System
An Experimental Investigation on Rotary Ultrasonic Machining
Research on CMP Process Parameters Effect on Slurry Transport
Properties of Granite Grinding Surface
Study on the Correlation of Toughness Index and Wear Stages of Diamond
Measurement and Analysis of Cutting Forces in Circular Sawing of Granite
Wear Resistance Analysis of Plateau Honing Surface for Ceramics Mg-PSZ
The Toughening Effect of ZrO2(Y2O3) on SiC Bonding Polycrystalline Diamond (PCD)
Grinding Titanium Alloy (Ti-6Al-4V) by Cryogenic Cooling
Investigation of an Atomic Force Microscope Diamond Tip Wear in Micro/Nano-Machining
Microcutting of Polymethyl Methecrylate by Atomic Force Microscope
Research on Mechanism of Chip Formation at Small Size Cutting
Rubbing Process and Monitoring of Precise Ceramic Ball
Analysis of the Polished Surface Layer on the Glossy Granite Machined by Diamond Abrasives
Research on Increasing Diamond-Holding Strength of Saw Blade Segment Matrix
An Investigation into the Effects of Rare Earth on the Properties of Fe-Based Diamond Composites
On the Diamonds in Contact Zone of Saw Blade
Research on Metal Cement Grinding Wheel for ELID Precision Mirror Surface Grinding
Study of Acoustics Characteristics of Bending Vibration Disc --- Theoretical Analysis
Study on Application of Grinding Wheel for Bearing Internal Grinding
Creep Feed Grinding of a Nickel Base Superalloy with a Segmented Wheel Containing Coated CBN
Research on Optimization of Technological Parameters for Grinding Bearing Race
Determination of the Character of Grinding Wheel in Form Processing of High-Speed Steel Cutter
The Research and Application of Honing Technology
Study of Assembled Electroplated CBN Gear-Honing Cutter
Dynamic Response on the Ceramic Surface Residual Stresses for Grinding Temperature
Computer Simulation Technology in the Process of Shaping Milling Cutter Relief Grinding
The Research of the Deep-Hole Strong Honing of Titanium Alloy
Study on the Technology of New Ultrasonic Honing
On Trans-Characteristics of Coarse Grit Ultrasonic Honing Hard-Brittle Materials in the Ductile Mode from Brittleness to Ductility
Research on Relationship between Surface Waviness in Ground Bearing Race and Technological Parameters
The Application of ELID Grinding Technology on External Precision Mirror Surface
The Defects and Solutions of the Surface Quality in Grinding Process
Fuzzy Estimation of Uncertainty for Grinding Force
The Application of Linear Motor in High-Speed Precision Cylindrical Grinding
The Application of ELID Grinding Technology in Precision and Super-Precision Grinding of Hard and Brittle Materials
Research on Intelligent Localizing Technique for Complex Curved Surface Parts Grinding
A Novel Biglide Parallel Grinder
A Study on the Movement Accuracy Analysis and Control for CNC Grinding Machine
The Application of Intelligent Fuzzy Control Technique to Grinding Long-Thin Shaft
An Electro-Hydraulic Grinding Feed Drive Digital Control System
Machine Tool Spindles and Active Magnetic Bearings
Study of High-Speed Positioning System Actuated by Stepper Motor
Research on Curved Surface Grinder with 5-DOF Paralled Mechanism
Design of CNC System for Beam-Rotatable Grinding Machines
Research into Bit for Extra-Hard Rock
Advances in Abrasive Processes
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
