Chapter
Discing Around Perforations of Thin Plates and Tubes by Hemispherical-Nosed Missiles or Spheres
Feasibility and Reliability of Genuine Solid State Press Bonding of Aluminum Alloy 5083
Stress Field near Crack Close to Bonding Interface in Explosion Clad Plate
Variable-Amplitude Fatigue Strengths of Fiber-Metal Laminate: GLARE
The Failure of a Pretensioned Thin Al Strip under Irradiation of a Laser Beam
A Microcrack Based Continuous Damage Model for Brittle Geomaterials
Environment-Assisted Cracking of Thermostat Bimetal in 3.5% NaCl Solution
Modelling of Deformation Textures of Cold Rolled BCC Metals by the Rate Sensitivity Model
Plasticity in Mono-Crystalline Silicon under Complex Loading Conditions
Dislocation Structure and Deformation Mechanism for the Anomalous Yield Behavior in Fe3Al Intermetallic Alloys
Modelling Screw Dislocation Mobility in the Bulk and in the Vicinity of Crack Tips using a Peierls-Nabarro Approach
Microscopic Observation of Plastic Deformation of Polycrystalline Iron
Single Grain Analysis of Strain Hardening and Internal Stresses in Cold Rolled IF-Ti Steel with a new High-Resolution Microdiffraction Technique
Self-consistent Estimates for Nonlinear Viscoelastic Polycrystals: a Simplified Resolution of the Affine Formulation Adapted to Monotonic Loading Paths
Microscale Spatial Distribution of Dislocations and Long Range Internal Stresses in Cold Worked bcc Fe
X-Ray Microbeam Diffraction Studies of Large Strain Dislocation Substructure Formation in OFHC Copper
Moving Plastic Discontinuities Effect on Overall Behaviour of Metals
High Temperature Plastic Deformation and Microstructure of Fe-9at%Si Polycrystals
Evolution of Grain-Scale Microstructure during Large Strain Simple Compression of Polycrystalline Aluminium
Practical Constitutive Models Covering Wide Ranges of Strain Rates, Strains and Temperature
Crash Analysis of Thin-Walled Structures with an Elasto-Plastic Explicit Finite Element Method
Ductility and Brittleness Simulation during Micro Void Evolution Process of Ductile Material Using Rigid Plastic FEM Based on Gurson Type Yield Function
Interpretation of High Strain-Rate Tested Results by Micrographic Evidence
Behaviour Characterisations of Sheet Metals, Metallic Honeycombs and Foams at High and Medium Strain Rates
The Effect of Strain Rate and Martensite Volume Fraction on Tensile Impact Behavior of Dual Phase Steels
Effect of Soft Material on Insulating Impact Pressure into Explosive
Ballistic Performance of Hot Isostatically Pressed (HIped) Ti-Based Targets
Dynamic Yield Stresses of Porous Materials Made of Bronze and Iron
Influence of Axial Pre-Load on Plastic Failure of Beams Subjected to Transverse Dynamic Load
Rate-Dependent Constitutive Law and Nonlocal Spallation Model for Concrete Subjected to Impact Loading
Characterization of Strain Rate-Dependent Shear Response of 63Sn/37Pb Solder under Uniaxial Torsion
Dynamic Response of an Elastic-Plastic Free-Free Beam Subjected to Impact at any Cross-Section along its Span
Saturated Impulse of Elastic-Plastic Beams under Concentrated Pulse Force
Effects of Damping on Dynamic Plastic Response of Circular Plate
Embedded Cell Model of Three-Dimensional Two-Phase Composites
Constitutive Behaviors of Discontinous Reinforced Composites
Plasticity Theory for Particulate Composite Materials with Imperfect Interfaces
Micromechanical Analysis for Off-Axis Nonlinear Behavior of Unidirectional Carbon Fiber Composite at Room and High Temperatures
A Variational Method for Fiber Stress Profiles in Unidirectional Composites with Matrix Creep
Basic Study of Progressive Crushing Mechanism
Numerical Simulation Technique for Progressive Crushing Behavior of FRP Tube under Impact Loading
Study on the Stress and Failure of Elastic-Plastic Interface for Fiber Composite
Tensile Properties of Thermoplastic Weft Knitted Composites
Effects of Fine-Particle Addition on Plasticity of Polymer Composites
Static and Dynamic Tensile Responses of Glass Woven Fabric Reinforced Composites
Orientation Relationship and Mechanical Properties of Rolled Polypropylene Sheets
Mechanical Properties and Fracture Mechanisms of Fiber Reinforced PBT/PC/Elastomer Blends
A Parametric Analysis of Surface Quality in Diamond Turning of an Al6061/SiCp Metal Matrix Composite
An Investigation of Surface Roughness Formation in Ultra-Precision Machining of Al6061/SiCp Metal Matrix Composites
The Localized Internal Necking Process between Microvoids in a Plastic Solid
A Study of Adiabatic Shear Plugging in Ti6Al4V Alloy
A Simplified Approach to Material Instability under High Strain-Rate Stretching
Strain Gradient Effect on Initiation of Adiabatic Shear Localization in Metal Matrix Composites
FEM Simulation of Torsion Tests for Pre-Deformed Lead with Work-Softening
Transformation Conditions in SMAs under Multiaxial Stress State: Experiments and Simulations
Constitutive Equation and Computational Simulation of Deformation Behavior of TRIP Steels
Deformation Behavior of Elastic-Plastic Materials Containing Instantly Transforming Inclusions
Transformation Condition in a Fe-Based Shape Memory Alloy Under Thermomechanical Loadings
Transformation Induced Plasticity in Maraging Steel: An Experimental Study
Prediction of Mechanical Properties of TRIP Steels by FEM and Micromechanics
Some Deformation Features of Polycrystalline Superelastic NiTi Shape Memory Alloy Thin Strips and Wires under Tension
Superelastic NiTi Memory Alloy Micro-Tube under Tension— Nucleation and Propagation of Martensite Band
Analysis of Tensile Strength of Y2O3 Stabilized ZrO2
Homogenous Rolling and Texture Modelling in Cold Rolled Low Carbon Steel
Springback of Laterally Loaded Circular Plates
Deep Drawability of 5083 Al-Mg Alloy Sheet at Elevated Temperature and its Prediction
An Inverse Problem of Reinforced Panels Forming
FE Analysis of Springback in Hat-Bending with Consideration of Initial Anisotropy and the Bauschinger Effect
Computer-Aided Process Design for Tension Levelling of Clad Sheet Metal
Direct Evaluation of Sheet Metal Forming Properties under Various Deformation Conditions
On Alternative Representation of Forming Limits
Computer Aided Process Planning (CAPP) System for Non-Axisymmetric Deep Drawing Process
Experimental Study on Large Deformation in Fine-Blanking Process by Implementing Different Stripper Designs: Vee-Ring Type Vs. Plate-Type
A Study on Microstructure and Texture Evolution in Homogeneously Cold Rolled 93/7 Brass
Determining and Valuation the Zones of Minimal Reserves of Working Capacity for Concave and Convex Die
Experiments and Analysis of the Effect of Local Induction Heating on Deformation
Numerical Simulation of Non-Adiabatic Shear Banding in Metal Forming Process using Finite Element Method
Deformation Characteristics of Helical Gear with Small Bevel Angle during Net Shape Forging Process
Effect of Alloying Element on the Mechanical Behavior and Superficial Defects in Thixoforged Components of Al-Si Alloys
Finite Element Numerical Simulation Modeling for Reheating Process of Semi-Solid Forming
Design and Analysis of a Computer Integrated Open Die Forging Cell
Measurement of Friction Characteristics using a Three Pin System
An Internal Variable Approach to Superplasticity of Microduplex Pb-Sn Alloys
The Effect of Temperature and Strain Accumulation on the Superplastic Deformation Behavior of an Al-Cu-Zr Alloy
Superplasticity-like Deformation of a Coarse-Grained Al5052 Alloy
The Parameter Identification of Superplastic Constitutive Model Using Optimization
Texture Evolution during Low Temperature Superplasticity in Aluminum Alloys
The Strain Rate Cycling Induced Superplasticity and its Computer Optimization in Titanium Alloys
Discussion on Constitutive Equations of Fine-Grain Superplasticity
A Study on the Tensile Deformation of Superplastic-Like Al-Al3Ni Eutectic Alloy with [111] Fiber Texture
Electron Backscattered Diffraction Study on Superplastic Properties of Coarse-Grained Fe-27at.% Al Based Alloys
The Effect of Reinforcement on Superplastic Flow in Powder-Metallurgy Processed Aluminium Matrix Composites
Research of Al-Zn 10-Mg-Zr Superplastic Alloy
Cavity Nucleation at Particles during Deformation at Elevated Temperature
Coupled-Multilevel Modeling for Hot Deformation and Sintering
Improvement of Post-Deformation Properties by Static Annealing for a High Strain Rate Superplastic Composite
Project of 'Towards Innovation in Superplasticity' in Japan
Softening Effects in the Bending of Tubular Structures and Components
Practical Computation of the Plastic Collapse Limit of Defective Pipelines under Complex Loadings
Dynamic Buckling of a Column with Adhesive Bonds
Collapse Analysis of Thin-Walled Structures by Finite Element Limit Analysis
The Characteristics of Collapse for Thin-Walled Members by Inclined Impact Load
Dynamic Plastic Buckling of Circular Cylindrical Shells Under Axial Impact
Modeling of Elastic-Plastic Beam-on-Foundation
Finite Element Analysis of Thin Walled Tubes under Point Loads Subjected to Large Plastic Deformation
Experimental Studies of Thin-Walled Circular Aluminium Tubes under Axial Loading
Large Deformation Model of Flat-topped Conical Shell under Axial Compression
Large Plastic Deformation of W-Beams Used as Guardrails on Highways
The Load Carrying Capacity of the Pressure Vessel with Two Defects along Axial Direction
The Calculation of Shakedown Loads for Contact Problems
On-Line Measurement of Heat Generation by Plastic Deformation in Some Structure Members
Hybrid Control of Inelastic Structures during Earthquake
Thin - Film Forming of Cluster Diamond-Dispersed Aluminum Composite by Dynamic Compaction
Microstructure and Friction Properties of Cluster Diamond Dispersed Cu Composite
Structural Analysis for Lightweight Design of a Seat Frame in Automotive Vehicles
Gradient Aspects of Crystal Plasticity at Micro and Macro Scales
Advances in Engineering Plasticity
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
