Chapter
Interfacial Studies of Carbon Fibre Reinforced Composites
Macroscopic Characterisation of Failure in Composites Materials
Invariant Polynomials for Composite Strength
Characterisation of Polymers in Mixed Waste Streams Using Ultrasonic Broadband Attenuation Analysis
Recovery of Polyol from Flexible Polyurethane Foam Wastes
Empirical Modelling of the Tensile Properties of High Impact Polystyrene in Terms of Its Secondary Phase Morphology
Factors Affecting the Grain Growth of Austenite in Low Alloy Steel
Factors Affecting Deformation of Electrodes when Resistance Spot Welding Coated Steel
Influence of Welding Speed on the Solidification Structures when Resistance Seam Welding Thin Mild Steel Sheet
Wear Mechanisms in High Speed Steel Circular Saw Blades when Machining Cupro 107, Inconel 600L* and Nimonic PK31* Nickel Based Alloys
The Effect of Increasing Sample Width on the Strength of Weldbonded Lap Shear Joints
The Corrosion/Erosion Induced Premature Failure of Some Draught Fan Blades in a 250 MW Boiler
Determination of Creep Damage in the ODS Superalloy MA6000
The Effects of Thermal Treatments on the Stress Corrosoin Cracking Resistance of Forgings of the Aluminium Alloy 7010
Oxidation/Sulphidation of Ti and Ti-6Al-4V at 750°C Alloy
Scanning Probe Microscopies-Applications in Material Science
Auger Electron Microscopy, AES, a Powerful Tool in the Non-Destructive Identification of Service Embrittled Turbine Bolts
New Thermal Energy Sources of H, O, Cl and N Atoms for Material Processing
Effects of Ultra Violet/Ozone Oxidation on the Surface Chemistry of Polymer Films
Surface Analytical Studies of Magnetron Sputtered Titanium Nitride (TiNx) Coatings
Optimisation of Heat Treatments for Oxynitride Glass-Ceramics
The Role of Rheology, Zetapotential and Radiographical Analysis in the Slip-Casting of Silicon Nitride for Advanced Applications
Bonding Silicon Nitride Using Glass-Ceramic
Sol-Gel Preparation of Mixed Lanthana-Ceria Systems
Optimisation of Alumina - Silicon Carbide Dispersions and the Fabrication of Nanocomposite Ceramic Materials
Fabrication of Silicon Nitride-Silicon Carbide Nanocomposite Ceramics
The Autocatalytic Ageing of Yttria-Tetragonal Zirconia Polycrystals (Y-TZP)
Oxidation of Porous Bonded Silicon Carbide
Preliminary Studies of TiN Particulate-Reinforced Si3N4 Matrix Composite (Syalon 501) Following Exposure in Oxidising and Oxy-Chloridising Environments
Low Amplitude Oscillatory Wear in Yttira-Stabilised Zirconia
Diamond-Like Carbon Coatings for Biomedical Applications
Effects of Implant Material Properties and Implant-Bone Bonding on Stress Shielding in Cementless Total Hip Arthroplasty
Fluoride Release from Glass Polyalkenoate (Ionomer) Cements
The Evaluation of Dental Glass Ionomer Luting Cements by Static and Dynamic Testing
A Study of High Adhesion Properties of Gold on Surface Modified Flexible Polytetrafluoroethylene Substrates for Use in Medical Implants
The Modelling of Crack Propagation through the Interfacial Region of a SiC/Titanium Metal Matrix Composite
Suitability of Applying Advanced Surface Engineering Treatments to High Speed Steel Circular Saw Blades of Commercial Quality
A Model of the Pressure Distribution within Ultrasonically Energised, Polymer Suspended Abrasive Used for Surface Finishing Moulds and Dies
Detection of Absolute Number Densities of Atomic Hydrogen in Diamond-Like Carbon (DLC) Deposition Plasmas
Detection of Atoms Sputtered from Surfaces
Laser Ablation of YBa2Cu3O7-x Thin Films
Advances in Engineering Materials
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
