Chapter
Image Analysis for Full-Field Displacement/Strain Data: Method and Applications
Application of High Speed Image Correlation for Measurement of Mode Shapes of a Car Bonnet
Use of Integrated Simulation and Experimentation to Quantify Impact Damage
Validation of Impact Simulations of a Car Bonnet by Full-Field Optical Measurements
Comparison of Numerical and Experimental Strain Measurements of a Composite Panel Using Image Decomposition
Session 2a: High Speed Imaging for Dynamic Testing
High/Ultra-High Speed Imaging as a Diagnostic Tool
Approaches to Synchronise Conventional Measurements with Optical Techniques at High Strain Rates
Performances and Limitations of Three Ultra High-Speed Imaging Cameras for Full-Field Deformation Measurements
Damage Observation and Analysis of a Rock Brazilian Disc Using High-Speed DIC Method
Session 2b: Foam Materials and Structures
Assessment of the Deformation of Low Density Polymeric Auxetic Foams by X-Ray Tomography and Digital Volume Correlation
Strength Hypothesis Applied to Hard Foams
Characterisation and Modelling of a Melt-Extruded LDPE Closed Cell Foam
Verification of a Finite Element Simulation of the Progressive Collapse of Micro Lattice Structures
Session 3a: Welding Stresses
Model Updating for a Welded Structure Made from Thin Steel Sheets
Using Digital Image Correlation Techniques and Finite Element Models for Strain-Field Analysis of a Welded Aluminium Structure
Validation of Welding Simulations Using Thermal Strains Measured with DIC
Local Elasto-Plastic Identification of the Behaviour of Friction Stir Welds with the Virtual Fields Method
Session 3b: Fracture Mechanics
Fatigue Crack Initiation and Propagation in SuperCMV Hollow Shafts with Transverse Holes
Accurate Measurement of Opening Displacement of Notch with Moiré Interferometry by Changing Applied Load
Understanding Crack Tip Plasticity – a Multi-Experimental Approach
Experimental and Theoretical Study of Fracture Paths in Brittle Cracked Materials Subjected to Pure Mode II Loading
Session 4a: Advances in Digital Image Correlation
Assessment of Measuring Errors in Strain Fields Obtained via DIC on Planar Sheet Metal Specimens with a Non-Perpendicular Camera Alignment
Digital Image Correlation Techniques for Analysing the Deformation Behaviour of Compacted Graphite Cast Irons on a Microstructural Level
Error Estimation of DIC for Heterogeneous Strain States
Full-Field Deformation Measurement via one Element Q-DIC
Session 4b: Impact and High Strain Rate Behaviour
Experimentation of Steel Fiber Reinforced Concrete Tri-Axial Split Strength under Quasi-Static Loading and High Strain-Rate
Experimental and Numerical Characterization of the Impact Response of Polyethylene Sandwich Panel: A Preliminary Study
Numerical Simulation and Testing of Water Impact of Structural Attachment Elements of a Reusable Thermal Protection System
Dynamic Behavior of Advanced Ti Alloy under Impact Loading: Experimental and Numerical Analysis
Session 5a: Material Behaviour
Investigation of the Friction Variation with Sliding which is Commonly Observed in Individual Fretting Test Cycles
Effect of Indenter Geometries on Material Properties: A Finite Element Simulation
Determination of a Rubber-Like Material Model as an Inverse Problem
Effect of Viscoelastic Behavior on Electroconductivity of Recycled Activated Carbon Composites
Analysis of the High Strain-Rate Behaviour of Polyethylene Based Nanocomposites
Session 5b: Measurement Innovations
A Phase Compensation Technique of Sampling Moiré Method for Accurate Single-Shot Phase Analysis
3D/4D Strain Mapping Using In Situ X-Ray Microtomography
Stroboscopic Fringe Projection Method for 3D Dynamic Displacement Measurement
Speckle Pattern Characterisation for High Resolution Digital Image Correlation
Evaluation of the Integrity of a Human Molar under Compressive Loading Using 3-D Axial Tomography
Session 6a: Residual Stress
Ultrasonic Measurement of Residual Stresses in Welded Elements of Ship Structure
Measurement of Residual Stresses within a PWR Swaged Heater Tube
Determination of X-Ray Elastic Constants for Q1N Submarine Pressure Hull Steel
Finite Element Validation of the over-Coring Deep-Hole Drilling Technique
The Validation of Weld Residual Stresses for Use in Structural Integrity Assessment
Strain Evolution during Lap Shear Testing of SnCu Solder
Session 6b: Vibration Analysis
Model Updating of an Enclosure Using Imaginary Elements
Analysis of Forces in Vibro-Impact and Hot Vibro-Impact Turning of Advanced Alloys
Measurement of Tangential Contact Stiffness in Frictional Contacts: The Effect of Normal Pressure
Synchronization between Driving and Illumination Signals in a High Frequency Stroboscopic Imaging System
Vibratory Analysis of Turning Process
A Strategy for Delivering High Torsionality in Longitudinal-Torsional Ultrasonic Devices
Session 7: Validation Methods
Multi-Scale Modeling of Heterogeneous Materials and the Validation Challenge
Validation of Micro-Slip in Interference Fitted Shafts Subject to Complex Loading Regimes
Using Numerical Models to Complement Experimental Setups by Means of Active Control of Mobility
Session 8a: Damage in Composite Materials
Analysis of Nonlinear Shear Deformations in CFRP and GFRP Textile Laminates
Pulse Phase Thermography and its Application to Kissing Defects in Adhesively Bonded Joints
Application of FBGs Grids for Damage Detection and Localisation
Acoustic Emission Source Characterisation in Large-Scale Composite Structures
Dynamic Properties of Cortical Bone Tissue: Impact Tests and Numerical Study
Session 8b: Thermal Deformation
Coupled Thermo Mechanical Characterisation of Polymers Based on Inverse Analyses and IR Measurements
Experimental and Numerical Analysis of Thermal Deformation in Thermoelectric Coolers
Dynamic Response of Thermally Bonded Bicomponent Fibre Nonwovens
Analysis of Creep Behavior of Polypropylene Fibers
Experimental Investigation of the Deformation of Built-up Members of Cold-Formed Steel Profiles
Strain Analysis of Pipeline Test Specimens Containing Longitudinal and Circumferential Corrosion Defects
Session 9a: Photoelasticity
Experimental Study on Stress Field Parameters of an Interface Crack in Aluminum/ Epoxy
Determination of All Stress Components of Axisymmetric Stress State in Photoelastic Tomography
Effects of Ray Bending in Scattered Light Photoelasticity for Tempered and Annealed Glass Plates
Assessment of the Interface Shear Strength of Metal-Polymer System Based on the Single Filament Fragmentation Test Method
Spectroscopic Birefringence Mapping by Channeled Spectrum
Session 9a: Thermomechanics
The Effect of Plastic Deformation on the Thermoelastic Constant and the Potential to Evaluate Residual Stress
Thermoelastic Stress Analysis of T-Stub Model
The Application of Thermoelastic Stress Analysis to Evaluate Debond Damage in Composite Sandwich Structures
Non-Destructive 3-D Determination of Interior Stresses
Residual Stress Interaction against Mechanical Loading during the Manufacturing Process of an Assault Rifle Component
Advances in Experimental Mechanics VIII
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
