Description
This publication comprises Vol. 4 (supplement) of the Proceedings of the 5th International Conference on Aluminium Alloys, held in Grenoble, France, July 1-5, 1996, which addressed all aspects - experimental to modelling - of the physical metallurgy of aluminium alloys.
Particular emphasis was placed on processing, microstructures and final properties. The entire range of material applications is covered in this volume, e.g. transportation, packaging and building, and all Al-based materials have been included, such as Al-Li alloys, laminates, composites and ultra-fine structures, prepared using either conventional or novel techniques.1. Invited Lectures. 2. Casting and Solidification Processing. 3. Processing of Ingots, Billets and Strips. 4. Recovery, Recrystallization and Textures. 5. Alloy Constitution, Phase Transformations. 6. Plasticity and Strengthening. 7. Fatigue, Creep and Fracture. 8. Corrosion, Surface Properties. 9. Joining, Properties of Structural Components. 10. Alloy and Product Development.
Chapter
Structure and Property Control of Aerospace Alloys
Aluminium Alloys for Automotive Application
Alternative Materials for a New Generation of Vehicles
Effect of Cavitation Melt Treatment on the Structure Refinement and Property Improvement in Cast and Deformed Hypereutectic Al-Si Alloys
Rapidly Solidified Layers on an AlZn5Mg3Cu0.8 Alloy
Control of Segregation in Squeeze Cast Al-4.5Cu Binary Alloy
Numerical Method for Analysis of Microporosity Formation in Aluminium Alloy Castings
Indirect Extrusion of Different Al-Si-Powder Alloys
The Influence of Particle Dispersions and Processing Route in the Development of Recrystallization Textures in Aluminum Alloys
Analysis of Flow Behaviour and Texture Evolution of a Particle Hardened Aluminium Alloy in Plane Strain Deformation
Interaction between Iron and Cooling Rate from the Melt on the Dispersoid Distribution in AA 6013
Advanced Properties of Ultra Fine-Grained Al-Alloys
Comparison of Anisotropy and Flow Behaviour in Two AlZnMg Extrusions - Recrystallized versus Nonrecrystallized
Changes of Flow Stress by Plane Strain Compression of Al-Si-Cu Alloys at High Temperature
Measurements and Evaluation of Strain Rate Sensitivity in Al at Late Stages of Deformation
Tensile Properties at Low to High Strain Rates of AlMgSi and AlZnMg Alloys
Mg Effects on the Eutectic Structure and Tensile Properties of Al-Si-Mg Alloys
Precipitation Hardening Behavior of SiC Whisker Reinforced Al-Cu Based Alloys Composites
The Effects of Mixed Mode Loading on Intergranular Failure in AA7050-T7651
A Comparison of the Damage Tolerance of 7010 T7451 and 7050 T7451
The Effect of Processing on the Fracture Toughness of 8090 T8 Sheet
Toughness Enhancement Based on Fracture Mechanical Simulation of Al-SiCw Composite
The Cyclic Deformation Behaviour of Dispersion Strengthened Aluminium Materials at Elevated Temperatures
Theoretical and Experimental Studies of Galvanic Corrosion between Aluminium and Al-4% Cu Alloys
The Trivalent Chromium Pretreatment Applied to Aluminium 1050
Microcapsulated Aluminium Powders
Solid Phase Welding of Alloy AA6061 and SiCp Reinforced Alloy AA6061 at Intermediate Temperature
Fatigue Properties of Mechanical Fastening Joints
Industrial Applications of Superplastic Forming with Aluminum Alloys
Advanced Weldable High-Strength Al-Cu-Li Alloy for Aerospace Applications
Advanced Weldable Damage Tolerant AlMgLi Alloy for Aircraft Application
Al-Li Alloys for Lower Wings and Horizontal Stabilizer Applications
Weldable High-Strength Aluminium Alloys
Aluminium Alloys - Supplement of ICAA5
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
