Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).The 20th century was a period during which many new sciences and engineering techniques appeared and evolved, and were applied to industrial applications. Towards the end of that century, however, it was recognized that - in many cases - the industrial technologies that underpin current-day society suffered from wider sociogical deficiencies. The usual engineering approaches began to face many difficulties which arose from the high habitual levels of consumption of energy and resources.. Energy sources, and supplies of various resources, have already begun to diminish in the 21st century. These limitations on energy and resources require science and technology to adapt quickly to this new regimen.
As well as creating and developing efficient new technologies, those sciences and engineering methods developed in the last century have to be raised to much higher levels, of efficiency of energy- and materials-use, in the present century. Since materials science and engineering are the common factor in many industries, the “designing of interfaces for materials and their joints” which is an essential aspect of materials science and technology become key points for consideration in this collection.
Chapter
Hard a-Si3N4/MeNx Nanocomposite Coatings with High Thermal Stability and High Oxidation Resistance
Development of Telerobotic System for Remote Welding Operations in Unstructured Environment
Distribution of Zn and Interfacial Microstructure of Braze-Welding CMT Joints between Aluminium and Galvanized Steel Sheets
Reverse Monte Carlo Modeling of Atomic Configuration for Amorphous Materials
Hybrid Simulations for Desinging of Nano-Interfacial Structures
On the Fracture Mechanics Theory Called (MN-rp-σθ)
Experimental Determination fo Ga Activity in Liquid Ga-Sb-Tl Alloys by EMF Method
Reaction Diffusion in Diffusion Couples Ni-Al SolidSolution/Intermetallic NiAl and Ni/Intermetallic NiAl
Effects of a Small Amount of Ta on Diffusion Behavior of Carbon in Molybdenum
Characterization of (α+β)/β Transformation in a TC11 Titanium Alloy
Hydrogen Permeation in V-Nb Alloys
Transmission Electron Microscopy Observations on Cu-Mg Alloy Systems
Oxidation Behavior of SiC/TiAl Composite Material
Reaction of Sn to Nanocrystalline Surface Layer of Cu by Near Surface Severe Plastic Deformation
Interfacial Residual Stresses in Semiconductor Devices Measured on the Nano-Scale by Cathodoluminescence Piezospectroscopy
Direct Synthesis of Isolated L10-FePtCu Nanoparticles by RF-Magnetron Sputtering
TEM Studies on Phase Stability in Nanometer-Sized Alloy Particles
Electron Dose Rate Dependence of Phase Separation Induced by Electronic Excitation in GaSb Nanoparticles
Temperature Dependence of Internal Stress and Crystal Growth of Dilute Cu Alloy Films
In Situ Synthesis of Hybrid-Reinforced Titanium Matrix Composites
Development of Multi-Phase Intermetallic Alloy Composed of Ni3X-Type Structures
Collaborative Sintering of the Amorphous Alloy and Ceramic Powders for Nanocrystalline Composite Materials
Fabrication and Wettability Test of Silicon Nitrides with Ordered Protrusions
Preparation of Tungsten Carbide/Stainless Steel Functionally Graded Materials by Pulsed Current Sintering
Advanced CFRM Joint Device for Mover Engineering
Development of Freeform Fabrication of Metals by Three Diminsional Micro-Welding
Phase Change of Zr-Al-N and Nb-Al-N Films Prepared by Magnetron Sputtering Method
Rust Layers Formed on Weathering Steels by Long-Term Atmospheric Exposure to Industrial and Coastal Environments
Characterization and Dissolution Behavior in a Physiological Solution of Heat-Treated CaTiO3 Thin Films with Different Thicknesses
Oxidation Behavior of Mo-Si-B In Situ Composites
Electrical Property of TiO2 Thin Film Deposited by RF Sputtering
Classification of Oxidation Behavior of Disilicides
Corrosion Behavior of Pre-Treated Fe-Al Alloys in Aqueous Acid Solutions
Development of Large Area Plasma Reactor Using Multiple Low-Inductance Antenna Modules for Flat Panel Display Processing
Wear Properties of DLC and Plasma Sprayed WC Structure Coating
Preparation and Characterization of Hard (Ti,B)N Films by Ion Mixing and Vapor Deposition
Numerical Simulation of the Stress Field of Thick 7B04 Aluminum Alloy Board during Continuous Manufacture Procedure
Microstructure and Properties of Brazing Joint between YG8 Cemented Carbide and A3 Steel
Bonding Strength of W-Cu Joint by PECS Method
Room Temperature Micro-Bonding of Fine Wires to Foils
Evaluation of Compound Layer Formed by Impact Welding Using Phase Transformation Technique
Pulsed Electric Current Bonding of Tungsten to Copper with Intermediate Layer
Theoretical Approaches to Erosion and Wetting Phenomena during Laser Brazing Process
Prediction of Laser Fusion Zone Profile of Lotus-Type Porous Metals by 3D Heat Transfer Analysis
Study on Improvement of Oxide Layer and Properties of Plasma Sprayed Alumina in Thermal Barrier Coatings
Spraying Using Electromagnetically Accelerated Plasma
Adhesion Behavior of WC Coating Deposited on Titanium Alloy by Electrospark Deposition
Laser Cladding of Fe-Cu Based Alloys on Aluminum
Control of Microstructure by Laser Spot Heating
Resistance Welding by Inserting Wires between Joint Interfaces
Designing of Interfacial Structures in Advanced Materials and their Joints
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
