Chapter
Fracture Toughness of Ceramic Materials and Its Relationship to Chipping Formation
Strength and Fractography of Piezoceramic Multilayer Stacks
Thermography and Simulation as a Combined Method for Failure Analysis of PTCs
Fracture Origins in Miniature Silicon Carbide Structures
Nanofractography of Alumina by Scanning Probe Microscopy
Failure Analysis on a De-NOx Catalyst of a Large Waste Burner
Damage Growth in Porous Ceramics
Failure Analysis of Si3N4 Rolls for Wire Hot Rolling by Numerical Simulation of Thermal and Mechanical Stresses
Contact Strength of the RE-Oxynitride Glasses
Fracture and Fatigue Behaviour of Mullite/Molybdenum Composites
Polymer-Derived Al2O3-SiC Nanocomposites: Preparation Route vs. Microstructure
Fracture Toughness Enhancements through Stress Shielding in Functionally Graded SiC-TiC Composites
Development of Preparation Processes for CNT/Si3N4 Composites
Fracture and Crystallographic Phase Correlation in Alumina Based Particulate Composites
Quantitative Surface Fractography of Alumina and Alumina-SiC Composites during Diamond Grinding
Effect of Carbon and Nitrogen Implantation on the Properties of Silicon Nitrides
Fracture Resistance Evaluation of Fibre Reinforced Brittle Matrix Composites
Failure Behaviour of High Toughness Multi-Layer Si3N4 and Si3N4-TiN Based Laminates
Interfacial Fracture Toughness Measurement of Thick Ceramic Coatings by Indentation
Thermal Shock Behavior of an Al2O3/ZrO2 Multilayered Ceramic with Residual Stresses due to Phase Transformations
Failure Mechanisms in Directionally Solidified Alumina-Titania Composites
Fracture of Monoliths Fabricated by Stacking Water Processed Green Ceramic Tapes
Fracture Mechanisms in Laminates in the Alumina - Titania System
R-Curves in Al2O3 - Al2O3/ZrO2 Laminates
Contact Fatigue in Ceramic Laminated Composites
Carbon Nanotubes Prepared by CVD
Effect of Ion-Implantation on the Microstructure of Si3N4 Based Ceramics
Size Effects in Micro- and Nanocarbon Added C/Si3N4 Composite Prepared by Hot Pressing
Comparison of Silicon Nitrides with Carbon Additions Prepared by Two Different Sintering Methods
Effect of Rare Earth Oxide and Rare Earth-Alumina-Silica Glass on Mechanical Properties of Liquid Phase Sintered Alumina Ceramics
Mechanical Properties and Microstructure of α-SiAlON Based Cutting Tools
Influence of Alumina Platelets on the Mechanical Strength of Porous Zirconia Tape
Thermal Shock Resistance of Cordierite-Mullite Refractory Composites
Residual Stresses in Al2O3-ZrO2 Laminar System
Structure of Post-Creep Carbon Fibres
Nano-Indentation of SiC and Si3N4/SiC Ceramic Materials
A Contribution of Fractal Geometry to Characterization of Wear Process
Fractographic Studies of Sapphire Fibers Using Laser Scanning Confocal Microscopy
Study on New Ceramic Coated Metal Powders: Microstructure and Properties
Indentation Testing of MoSi2
Labeled Weibull Plot of a C-Derived Si3N4-SiC Nanocomposite
Thermal Shock Resistance of the RE-Oxide and Oxynitride Glasses
Fractographic Analysis of Surface Flaws in Glass
Determination of Dynamic Fracture Toughness of Si3N4 Ceramics by Instrumented Impact Test
Determination of Fracture Toughness and Fracture Probability of LPS Aluminas by Hertzian Indentation
Low Cost SiAlON from Pyrophyllite with High Hardness and Good Corrosion Resistance
Indentation Testing of an Al2O3/Al2O3 + ZrO2 Layered Composite
Thermal Stresses in SiC-Si3N4 Cubic-Cell-Divided Multi-Particle-Matrix System
Fracture Behaviour of Pressureless Sintered Nickel-Reinforced Alumina Composites
Residual Stress Profile Determined by Piezo-Spectroscopy in Alumina/Alumina-Zirconia Layers Separated by a Compositionally Graded Intermediate Layer
Mechanical Properties of Alumina/Zirconia Functionally Graded Material Prepared by Electrophoretic Deposition
Mechanical Properties of Thermal Barrier Coatings at Room Temperature
Effect of Oxidation at Elevated Temperature on Elastic and Interface Properties of Ceramic Matrix Composites
Mechanical and Fracture Properties of R-Glass Reinforced Composites with Pyrolysed Polysiloxane Resin as a Matrix
The Preparation and Properties of Functionally Graded Alumina/Zirconia-Toughened Alumina (ZTA) Ceramics for Biomedical Applications
PZT Ceramics Prepared from Two Phase Gels
Strength and Fractography of High Power Varistors
Delayed Fatigue of Hydroxy- and Fluorhydroxyapatite Ceramics in Simulated Body Fluid
Fracture Characteristic of Isostatic Pressed Submerged Entry Nozzle
Fractography of Advanced Ceramics II
Disclaimer: Any content in publications that violate the sovereignty, the constitution or regulations of the PRC is not accepted or approved by CNPIEC.
